Types of Cable Trays and their Uses

What are cable trays?


Cable trays are used to provide mechanical protection in areas where there are a large number of power control cables. Cable tray manufacturers design these to provide mechanical protection as well as a proper routing path for power or control wires. These wires may run both above and below ground.


In addition to technological advancement, the demand for skilful bolstering routines is also on the rise. Buildings and plants are becoming more computerised these days. Through sophisticated modes of cable and wire laying, the company provides fast, varied, and economic solutions to most present-day issues.


What are the materials used for producing cable trays?


Cable trays come in a variety of materials. They can be made of galvanised steel, aluminium, stainless steel, and glass-fibre reinforced plastic, among other materials. Choosing the right cable tray manufacturer is entirely dependent on the intended use and installation circumstances. The installation environment here refers to taking into account both electrical and corrosion factors.


Purpose of Using Cable Trays


Different types of cable trays answer different needs. The main reasons for using cable trays have been discussed below. 


Both power and signal cables are protected and supported by a cable tray system, making network upgrades, expansions, reconfigurations, and relocations easier.


Cable tray systems are often open to allow heat to dissipate, and can be easily replaced and repaired. Some cable tray systems are ideal for use under the floor, though they are normally suspended from ceilings or affixed to walls.


2 Essential Reasons for Using Cable Trays for your Business

1. You Will Save More


Cable trays are the best options to protect your wiring at a low cost. To begin with, cable trays are not too expensive to install. Furthermore, the installation of cable trays takes less time. And finally, installing a cable tray will always cost less than replacing wires. 


  1. Security Matters


When you expose your cables, you are not only putting yourself in danger, but you are also jeopardising your overall safety.

When there are cables strewn about, especially on the floor, the risks of slips, falls, and other mishaps increase. These are the kinds of mishaps you want to avoid in a workplace with employees and consumers.


What kinds of cable trays do industries use?


  1. Perforated Cable Tray


Cable tray manufacturers also recommend using Perforated Cable Trays. Perforated Cable Trays are made of a single component with a vented or solid bottom. They’re mainly used with power and control wires. They are available in three sizes: light, medium, and heavy-duty, depending on the needs of the client and the conditions on the job site. 


  1. Ladder Cable Tray

With smooth radius fittings and a wide selection of material/finish, the Ladder Type Cable Tray consists of two longitudinal side channels connected by individual traverse channels, providing substantial rail protection and system strength.


  1. Basket Cable Tray


Basket cable trays are commonly referred to as “go-to” solutions for routing and supporting multiple cable runs. Air circulation and cable ventilation are improved by the connected frame. This can be used under desks, on raised floors, or with hanging tray systems. Basket trays for intersections, horizontal portions, mounting bracing, hardware, and tray cutters can all be assembled.


  1. Raceways – Trunking Cable Tray


Underground cables and wires are commonly laid out using Raceway and Cable Tray Trunking. Our Raceway is available in single or multi-column configurations allowing simultaneous installation of one or more cable connections. Our products are widely used in the telecommunications, electronics, and electrical industries, among other industries.


  1. Aluminium Cable Trays


Aluminium cable trays are suitable for usage in a variety of settings. They’re known for having a good strength-to-weight ratio and excellent corrosion resistance. These cable trays are simple to install and have the added benefit of being lightweight. These cable trays are typically 50% lighter than steel cable trays, according to fastener producers in India.


  1. Stainless Steel Cable Trays


Cable trays made of stainless steel are also frequently utilised in a variety of sectors. They are dye-resistant to a high degree. Stainless steel cable trays are also known for their strong resistance to organic and inorganic compounds at extremely high temperatures.


  1. Solid Bottom Tray


The Solid Bottom tray is popularly known for providing the best possible protection to the cable. Solid bottom cable trays are being used in optic fibre installations when the cable sliding off could cause a system failure. By choosing a solid bottom cable tray, you can avoid electromagnetic interference and radio frequency interference.